The Engineering Projects

Prevent Data Loss Risk In Raid-Based Storage

Hi Guys! Hope you’re well today. Happy to see you around. In this post today, I’ll detail how to prevent data loss risk in raid-based storage. RAID (Redundant Array of Independent Disks) is a data storage virtualization technology used for data redundancy and performance improvement in an Operating System. It has redefined how storage systems store and retrieve data, and its architecture comprises multiple physical disk drive components distributed over one or more logical units.

Prevent Data Loss Risk In Raid-Based Storage

RAID levels vary from RAID 0 to RAID 51 (and beyond). Different levels have different types of redundancy offered; however, a compromise has to be made when it comes to fault tolerance and performance. Although different RAID levels provide significant protection mechanisms against data loss due to hardware failure of hard disks, the technology is not invincible. Therefore, it is advisable to safeguard your data from any unexpected loss when using a RAID array. If one of the hard drives in a RAID storage array fails, one should consider replacing it instantly. Not doing so or delaying it for too long can cause unexpected data loss as it is highly likely that the other hard drives will fail soon. This is because the entire batch of hard drives in a RAID array often has the same manufacturing date and service life. The type, manufacturer, and other atmospheric variations play an important role in the service life of the hard drives.

Contact Data Recovery Specialist

Preventing to get into such conditions of severe data loss is something you should never divert your focus from because it can be debilitating. Especially, it is more complicated to recover data when it comes to a complex storage system. If you are not well-versed in the required knowledge, you should not take the risk of opting for the DIY mode for recovering the lost data from your RAID system. At such times, it is recommended to contact a reliable data recovery specialist. Doing so can help rebuild the RAID system, bypass the hard drive failures, and examine if any updates are needed in the residing virtualized architecture. This can make the recovery attempt quite time-consuming but reassuringly successful. But for this, it is necessary to make sure that you are choosing the right service provider with proper experience and expertise to recover data in varied data loss events.  

Maintain a Back-up

Different types of RAID configurations operate on different redundancies to diminish data loss and develop a storage system architecture that can provide data loss prevention. Monitoring and recording a RAID array usage is an essential task to be included in the data recovery strategy for efficient business continuity. In severe conditions, the pre-defined recovery strategies may not be helpful and can cause severe data loss. Hence, it is crucial to maintain a back-up and be prepared for such unfortunate cases of system failure or data loss. In such severe conditions of RAID failure, the entire data can disappear forever. Even if a corrupted hard drive overtakes the RAID array's redundancy and the hard disks fail abruptly, it is possible to rebuild your RAID array and recover your data by getting in touch with an expert data recovery professional. Among a few renowned data recovery service providers, Platinum Data Recovery Services has been a prominent name in offering considerate services like G-RAID data recovery and other types of RAID data recovery services when your data has been disappeared or made inaccessible due to corrupted hard drives, flash drives, memory cards, or RAID. That's all for today. I hope you've enjoyed reading this article. If you have any questions, you can approach me in the section below. I'd love to help you the best way I can. Thank you for reading the article.

Design of a Load Cell

Hi Friends! Hope you’re well today. I welcome you on board. In this post today, I’ll walk you through the details on the design of a load cell. Strain gauge load cells are widely used in various applications. They work on the principle of varying electrical resistance with elastic deformation in the conductor. The strain gauge comprises thin wires which are affected by a change in environment. Expansion or contraction in a strain gauge occurs with varying temperatures which results in creating noise and lack of accuracy in measurement. The life of the device may also be affected due to corrosion that may occur in the elastic element. In addition to the possible deterioration, the load cell itself may cause safety issues with regard to the environment. For example, in a refinery or chemical industry, the ignition of flammable liquids or gases may occur due to the use of load cells. Therefore, they must be designed accordingly.

        Hermetically Sealed

Hermetically sealed load cells provide the best protection to the environment. The load cell is sealed by welding, using epoxy or glass-to-metal bonding. Pressurized inert gas is filled inside the cell. These load cells are standardized by Ingress Protection (IP) rating as air and watertight.

        Open

These are designed in normal indoor conditions or special outdoor environments. Soft resin or rubber covering is used for environmental protection in this type of load cell. However, the strain gauge becomes vulnerable to moisture and change in temperature due to this type of protection.

        Explosion-proof

As the name suggests, this type of load cell protects from any explosion that may occur within the device. If the internal cavities in a device or equipment are exposed to gases, these gases, once filled in the cavity, will lead to a potential explosion. An explosion-proof load cell is highly suitable for such conditions. Their rating is achieved by combining confinement, limitation of energy, and segregation. Other factors to consider when designing a load cell are:

•         The maximum weight that a load cell can measure is called Rated Capacity or rated load. Therefore, the load cell rated load must be greater than the weight to be measured in a system.
•         Overload Rating (Safe) is the maximum load that can be exerted on a load cell without causing plastic deformation while measuring the weight of an element.
•         Overload Rating (Ultimate) is the maximum load that can be exerted on the load cell without causing a fracture to the load cell.

•         Rated Output is the ratio of the electric output signal and the strength of the excitation voltage expressed in mV/V.
•         Zero Balance is the electric output signal with rated excitation voltage at no-load condition.
•         Excitation Voltage is the voltage for excitation transferred to the circuit.
•         Non-linearity defines the deviation of the calibration curve of the load cell from a straight line. It starts from zero loads up to the maximum capacity of the cell.
•         Hysteresis is defined as the difference in the cycle a load cell follows while increasing the load from zero to maximum and then decreasing it from maximum to zero.
•         Combined Error is calculated by measuring non-linear and hysteresis effects in combination.
•         Repeatability is the measure of the difference between readings of repeated loads under the same loading conditions.
•         Temperature Effect on Rated Output is the change in readings due to a change in temperature.
•         Temperature Effect on Zero is the change in the zero-reading due to a change in temperature.
•         Input and Output Resistance is the resistance of the circuit measured at the input and output respectively.
•         Insulation Resistance is the measured resistance between the circuit and housing of the load cell.

That’s all for today. I hope you’ve enjoyed reading this article. If you have any questions, you can ask me in the section below. Thank you for reading the article.

Evaluate Your Capital Spend Before Investing In The Oil & Gas Software

Optimizing the well cycle portfolio is done by assessing the investments secured by the company’s management and opting for software systems assigned to the operational needs. Allocation of funds for equipment, vendor contracts rigs and accounts constitute the bulk of expenses for each project. The use of capital planning oil and gas software, requires evaluation and quality assessment before money is diverted towards it. This could be a daunting task in a market where prices fluctuate daily. Are you aware of the needs before relying on an expensive complex software? We shall try to relieve your pain points, take a test and undergo proper trials before considering the next purchase. Then select a vendor who can put together the system for long-term use.

Testing Systems Vital Before Capital Spend

There are no standard measures by which different petroleum companies invest in an accounting software. Nor are there any specific criteria on the dashboard of the CEO that defines the tailor made processes. To maximize the scope and identifying the pain points the management will need to earmark the following:

• Demographics Of The Company – Its size, number of employees onsite and in the office, testing staff. Each department should be a part of the survey.
• Agile Automation Tools – The specifications for an upstream company will be different from a mid-stream organization. Integration of several processes will be tested.
• Researching The Business ECO-system before start of a new project or well cycle.
• Maintaining track of regulatory standards before implementing the software.
• The testing team will report the parameters that impact the purchasing decision of the capital planning oil and gas software.
• Close down negotiations with suitable vendors and contractors for your organization.

While there will be certain niche frameworks that define your organization, some general factors every company requires. In the case of bigger companies, some operations are centralized for convenience. They also have a primary hub for business analysis and employ various testing stacks. They can identify the areas where systems are deficit. Such lack of discrepancy necessitates a new software system for better compatibility. Eventually, this software will be valuable in supporting key financial decisions of the organization. It will also provide insights that can improve the well cycle management and accounts - which are the two most critical areas where complex systems are required.

Assess The Necessity With Employees

The staff in various sites understand exactly what works and they should be asked about the functions that impact, their performance. At the corporate level, the management team can only map the plans theoretically. However, the ground reality is, the employees have knowledge of the workflow and what hurdles they face. If your organization is already using a software system, you are experienced to classify the areas where it does not perform to its optimal degree. Before buying a new Capital planning oil and gas software the above testing is crucial. For example, the accounts department allocates funds to every other subdivision. Ask the team about the current software functions.

• Are all the features being implemented?
• Does the software adhere to and achieve all the requirements?
• Do they have other expectations from the system?
• Would they consider improvisations?
• Which areas should be given priority for better performance?

Survey other departments by speaking to the users directly. Present the report to the decision makers, so they know where the funds have to be allocated. Such an exercise will help to improve the workflow and the productivity. The survey should address:

• Flow of operations required at the rig site and all productive wells
• Current compliance stipulations for data
• Financial reports preparation according to survey and intel
• Integration of new system with existing ones
• Training, maintenance, and support essential of the systems
• Make a dashboard of tracking jobs, teams, and tasks
• Each department should be enabled to access only the part of the system that they need.
• Consider the industry needs and separate data entry and access via a single central hub.

Time To Save The Petrodollars

It is difficult to control the fluctuations in the oil prices. But with technology-driven functions efficiency can be achieved. Your choice of capital planning oil and gas software can offer ideal time and money saving solutions. You will be able to anticipate needs in many areas with the accurate method. Even if you have special needs, a structure can be tailor made by evaluation, testing tools and processes that allow consolidation of data. Your decision making process can be improved by having multiple ledger classifications in the accounts department.

Why Creative Thinking is Important for Web Design Projects

If you look in the past, having a website was enough to generate leads and keep yourself running in the business. But today, the concept of a website has emerged to the whole new level. It is not only a source for your business but a platform to gain exposure globally. With the advancement in the competition, the companies are investing heavily on their websites to achieve maximum ROI. If your website doesn’t get successful in grabbing customers attention at first, then your competitors take up your place. That’s why creativity is essential!

Web Design: what's audience looking for?

If you think of a design and start implementing it right away - you won’t get the results no matter how creative, you go. At first, you need to put yourself in the audience shoes, think about what they are looking for? What interests them? What features attract them? Does animation move them? What is the first impression you’re making from your website? The second most crucial factor in bringing the website in your audience attention is the keywords. If your website is SEO-optimized, your audience will find you on the search engines and if not optimized, no matter how much effort you put - you’ll be missing from their list.

Fluidity and Adaptability

Once your audience land on your website, they look for the information they want. If they are looking to order something, they’ll go directly to the order page. But if your website is taking too long to load, then this might turn your visitors off.  The designers need to design each page creatively and organized for the incoming website traffic. Not only this, but the website also needs to be adaptable to all screen sizes. While some people still browse from the desktop, the majority view from their mobiles. If your website isn’t dynamite, it’ll have less readability and viewability. The summary is when you’re starting a web design, make sure it is adaptable to the OS and efficiently accommodate the size of the screen.

Learn to Stand Out

Social media has act brilliant in educating the customers; be it about the brand, design, marketing, or the happenings. The customer knows who’s the right fit for their needs. That’s why brands focus on building the campaigns that are audience-centred and revolves around their interest. When you design a website same as others are doing, your audience doesn’t find any engaging factor in it and withdraw you from the list. And grabbing the first impression is highly important. So, creativity is the factor that separates you from the rest, and unless you have innovative ideas that will work for you, don’t start the project.

Creativity in Website Branding

Your website speaks about you. It defines your objective, mission, vision, achievements, and everything you want your customers to know. People can learn about you with a simple online search that’s why big brands spend considerable time in creating a web design that appeals to their customers and conveys the information creatively. A silent message, short video, whiteboard animation, or a great story that clicks your audience. Learn what your audience is searching for and answer them through visuals. Use the power of social media to grow your brand reach. Images, color theme, and text should reflect the tone of your company. If you search some of the successful brands like Starbucks, Adidas, Amazon, Apple - you’ll find an X factor in it, be it the idea, design, tagline, or the style. Innovation and creativity pique the audience interest in your brand. So, when you come up with an idea which your audience hasn’t seen before sparks their interest and lead the customer down the conversion funnel.

Sound Financial Advice For Recent College Graduates

Hello friends, I hope you all are doing great. In today's tutorial, we are going to share some Sound Financial Advice For Recent College Graduates. After four years in college earning that degree, you're ready to begin climbing up the ladder of your chosen career. Now you have to think about what you want to do with the salary your new job pays. Yes, you want a new car, nice clothes, and a big apartment, but hold on—what you really need is a financially stable future. It starts now.  Some sound financial advice for recent college grads is listed below.

Use Credit Wisely

Credit becomes necessary when buying a new home or car. You begin building a credit history and score by paying monthly bills like your cell phone and electricity. Your credit score also rises and falls according to your student loan payments and any defaults. The average monthly payment on a student loan is about $280, according to the Colorado Department of Higher Education. By accepting the lowest monthly payment, you'll have more cash to save. You can choose to pay it off faster, but you lose the savings and the higher credit score you earn by paying on time every month. Unsecured credit cards are a double-edged sword: They can lead to a mountain of debt that compounds with high interest, but they are also a way to build a high credit score and a resource to use in case of an emergency. Choose a credit card with a low fixed interest rate and low fees. Start with just one, use it wisely, pay it off each month and keep a low credit line ($500 or less). Watch out for low-interest rates with high fees; the fees negate the interest rate. You are entitled to one free credit report a year, too, so take advantage of this and monitor your credit.

The Cost of Living

"When choosing a place to live, look at the big picture before committing to a lease," says Allen. If you have roommates and the living arrangements agree with you, stay there. Splitting rent and bills saves a lot of money. If you choose to live alone, consider the actual amount of time you spend at home and the room you need to live. Single living doesn't take much room, and a two-bedroom apartment may mean you'll waste money on space no one uses. A one-bedroom or a studio apartment costs less and still gives you room for comfort. Your monthly bills will cost more than necessary if you don't comparison shop. If you live in an area with more than one energy provider, you're lucky, because the competition keeps the price down. And just because your parents or roommates have a bundled cable, Internet and phone contract with a big company, doesn't mean you have to follow suit. Shop around to find the best deal, and always ask what your monthly bill will be once the promotion ends, as some packages almost double in price after the initial promotion.

The Budget

For budgeting help, use a program like Mint.com. It's free, and it will organize and categorize your spending for you. Most experts agree that 10 percent of your monthly gross pay is what you should save at a minimum. To make saving easier, set up a savings account and have the amount automatically deducted from each check. You never see it, which makes saving easier.

Why should we use Torch Lighters

Lighters are popular for the cigar smokers but not only have the smokers used the lighters but also for the people who are interested in camping, picnicking and any other activities in the outside the windy environments. Usually, cigar smokers prefer butane torch lighters during the smoke. A torch lighter is a portable thing that is used for instant flame or fire. It is used for many activities like outside cooking, lightening in the dark area, fishing, and many many activities. Butane torch lighter in an instrument that is worked by utilizing butane creates hot flames. If you can’t buy a good torch lighter, it can make you in trouble in a serious condition. Suppose you are when you need instant fire and you have a lighter and unfortunately your lighter is not working, just think about that feeling. There are many reasons for not working your torch lighter. If you can identify those, then you can avoid the situation you don’t want. These reasons are described below why torch lighters stop working.

1. INCORRECT BLEEDING

It’s important bleed the lighter correctly because incorrect bleeding can be the reason for not working your lighter properly. You should bleed your lighter when the flame drops and fuel tank about to be empty; the fire is not frequent. During the bleed, turn off the gas valve, position the light up a stand that the port is facing the floor, then put a small screwdriver into the port and press. Keep the pressure until the hissing sound stops. Then continue pressing for a few more seconds for making sure escape the air.

2. NON-PREMIUM FUEL

The quality of your fuel is very much dependent on the quality of your lighter. If you don’t put premium fuel to your lighter, it will affect your lighter. Non-premium fuel can cause longevity and work. If you are not skimped about the fuel, then your lighter will work properly. Inexpensive fuel or butane is poorly refined or not adequately refined, which is very harmful for the torch because it contains microscopic impurities. The port of torch is tiny that’s why it can create a focused flame and the impurities refined can block and once it blocked, it is very much difficult to unblock them. You should continue with better fuel or butane.

3.INCORRECT REFILLING

Your lighter can be malfunctioned if you refill your lighter incorrectly. Incorrect refill sometimes means the air will insert the fuel tank, and it malfunctions the work of a lighter. To avoid this situation, every time you do it by the position of the torch upside down. So during the refilling fuel, be careful. Put the nozzle directly to the gas valve and firmly press it a couple of seconds when you feel that the hissing stops, the tank becomes full stop the press. This is the process of refilling the tank correctly. Know of it.

4. ALTITUDE

Altitude problems can occur in butane torch lighters. There are the functions of fuel and air ratios, which are mixtures of different fuel. If you use non-premium fuel, then this altitude problem can occur. When the lighter refilled in a lower altitude and it is operating it, then it is a higher possibility to occur an airlock with a valve. If the partial release of pressure is done with the adjustment valve, then it can unlock the air.

FLAME ADJUSTMENTS

The flame adjustment will be needed if your torch is not working properly, such as the flame too high or too low. Adjust the flame by using the (-), (+) button in front of the torch. If you have fueled inexpensive fuel and bled incorrectly, then it can be the flame change problem. Lighters are very much important for those people who spend a lot of time outside the home and especially at night. The smokers are required the torch lighters more than the other. Though people can use matches, I think torch lighters is more convenient and portable and also economical than the matches. However, it is very helpful for our many types of activities. So it is also can be a troublemaker if it is not working properly. For making it works properly you have maintained certain things I have described above, if you follow those things and keep maintaining then you will experience a better use of torch lighters.

The Key Benefits of Data Visualization

Hi Friends! Hope you’re well today. I welcome you on board. In this post today, I’ll walk you through the key benefits of data visualization. Data visualization is something that used to be a competitive advantage, but now it is becoming a necessity to survive. I have outlined some of the key benefits of data visualization and I will explain each point very briefly. If you take one thing away from this post it should be that data visualization is important and you should be implanting data visualization techniques into your business or organization.

Reducing Errors

Keeping track of your data will let you tell a story about your customers and your business. One negative part of the story is that data visualization will let you identify the problems that are happening with your company. For instance, if you analyze your data as an eCommerce business and see that a large percentage of your customers are getting to the checkout and then abandoning their cart, then you are now aware that something is wrong. You could use the data to infer that something is off with your check out system and that you need to make improvements. Testing out new checkout pages could boost your conversions, and that is just one basic way of how knowing your data can reduce errors in your business. There is a good chance that if a company has never used data to identify errors, then they will find ways to limit errors and improve their business from data visualization.

Identify Trends

By using data visualization, you will know what kind of trends are going on with your business and the industry that you are in as a whole. Why would knowing trends help my business? Well, if you can identify trends before your competitors, then that is going to give you an upper hand right off the bat. Leaders in every industry are always looking at trends and seeing if there is a business opportunity in that trend. Usually, if you can be one of the people to capitalize on a trend, then you are going to gain a lot of market share. It is basic economics to know that the early movers and early adopters to a trend are usually the most successful. Use data to identify the trends, and then come up with ways to make money from the trend!

Improve Your Marketing

The last point that I have as a benefit for data visualization is that your marketing can drastically improve. A surefire way to improve your marketing is to look at the data that you have and identify where you can be more effective. It can also let you know which kind of marketing is unsuccessful and not profitable. If you know that something is not profitable, then you could make a much bigger return on investment if you put money into the marketing channels that you are seeing a great ROI! That’s all for today. I hope you’ve enjoyed reading this article. If you have any questions related to this article, you can ask me in the comment section below. I’d love to help you the best way I can. Thank you for reading the article.

Why EV Pickup Trucks Will Spearhead The Switch To Electric Motors

Hi Guys! Hope you're well today. Glad to have you here. In this post today I'll detail why EV pickup trucks will spearhead the switch to electric motors. In 2019, approximately 63 percent of Americans looking to buy a car were interested in buying an EV, according to Consumer Reports. The stage is set for major EV manufacturers to contend over the market. Of all body styles, pickup trucks seem to be of particular interest to them. General Motors, Tesla, and Ford are doubling down their efforts in EV pickup design. This is all so that models like the Hummer EV and the Cyber truck can release within the next few years. Trucks are favored for their towing power, traversal abilities, and relatively low need for maintenance. Those are perfect attributes for EV platforms to expand upon. Here are the top advantages EV pickups bring that will let them lead the switch to electric vehicles.

Pickups Will Make The Switch To EVs More Palatable

The first and most important reason EV pickups will lead the charge in switching to electric is because they appeal to a wider demographic. At least, that is the case in the United States. The latest data from Hedges & Co. shows that there are almost twice as many pickup owners in America as there are car owners. People from all walks of life find a use for pickup trucks. Hence, capitalizing on pickup trucks will make the switch to electric vehicles more attractive to the common driver. Jessica Caldwell, the auto analyst for Edmunds, says that everyday motorists are the key to bringing the electric dream to fruition, not enthusiasts. They would need to be convinced to change their behaviors to accommodate the differences in operating an electric pickup. But with the benefits that EV engines offer, manufacturers are optimistic that they can be made to see the advantages in making the switch.

Greater Capacity For Customization And Novel Features

With so many Americans expressing interest in EVs, selling EV trucks sounds easy on paper. However, General Motors’ Josh Tavel says that it's not as simple as that. The average Hummer buyer, he says, is not buying the truck to have a lower carbon footprint. The target demographic has always been monster truck and military enthusiasts, says Tavel. It has been this way ever since the vehicle first rose to popularity in the late 90s and early aughts. What they are marketing to are the adventurous and outgoing types. This market, GM says, overlaps significantly with engine-savvy car enthusiasts. If they can be made to adopt the electric engine, they can influence everyone else to do so as well. This is why they added some features they know will appeal to vehicle aficionados. These include novel additions such as a crab walk mechanism and intuitive graphic displays. . All these and more can be easily supported by an EV built from the ground up with efficiency as a focal point.

More Reliability And Power Than Traditional Trucks

Electric pickups could not have come at a more appropriate time. Nowadays, consumers are clamoring for efficiency and reliability. This is mainly out of concern for the environment. On top of this, however, people also want cars that are simpler to maintain and break down less. Current surveys point to a drastic shift from public to private transport soon. More than 78 percent of commuters will mainly rely on private vehicles for transport from now on. This was according to the 2020 EY Mobility Consumer Index. EVs have fewer moving parts. Thus, they are potentially more powerful and consistently reliable than internal combustion vehicles. Reliability is one of the most prized and sought after traits in trucks, according to consumer truck reviews and rankings.

Enhanced Performance For Commercial And Recreational Use

The increased towing power and dependability of EV pickups make them attractive commercial fleet vehicles. The long-range operation of electric trucks is more economical than fossil fuel ones. Headquarters and stop points could be established according to the trucks’ ranges and charging stations set up at these points. This way, refueling can be done overnight at the stops themselves, instead of on the road. A supply line like this can be vastly more efficient in terms of time and energy. As for recreational use, EV pickups can excel at carrying vacationing and camping equipment. This can be of particular appeal to suburbanites, who often vacation by going out into the wilderness to camp and kayak. With a fair number of Tesla owners, they would appreciate being able to do so in an environmentally friendly way as well.  More engine power can allow them to carry more gear, and longer range can let them make better headway before stopping.

Mutual Benefit For Consumers And Manufacturers

Auto manufacturers stand to gain much from the demand for EVs, especially in pickups. This is thanks to their high-profit margins and demand. The average price of a full-sized EV pickup is $50,000. Even so, they are easier to maintain and have better long-term performance. This makes them a more sensible long-term investment. Figuring out the right price point is a major point of emphasis for manufacturers. Ken Morris, vice-president of General Motors’ EV and self-driving vehicle division, voiced his views on this challenge. According to him, the tricky part will be to price the trucks low enough to make them preferable over traditional ones, but not so low that it hurts profit. This has turned out to be rather difficult with the 200-kilowatt-hour batteries that EV pickup specifications demand. These would cost $20,000 per unit, which is slightly more expensive than your average economy vehicle. These factors together make it easier for automakers to fund their R&D projects for better EV tech. Even with a higher mark-up, consumers simply accept this as a matter of course for a young technology. And thus, they buy the vehicle anyway. Although controversial, it certainly facilitates the rapid growth of electric vehicles. This growth will likely go faster from here on out. That's all for today. I hope you find this article helpful. If you have any questions, you can approach me in the section below. I'd love to help you the best way I can. Thank you for reading the article.

The Best Technologies for Catching Security Flaws in 2020

Hi Friends! Hope you’re well today. I welcome you on board. In this post today, I’ll detail the best technologies for catching security flaws in 2020. Security is a key priority for all organizations, and attacks have become increasingly specific. Usually, attackers take advantage of specific bugs or vulnerabilities to gain access to sensitive data. The cost of breaches can be huge, which is why organizations are equipping themselves with the best technologies aimed at catching vulnerabilities and security flaws before a potential hacker can take advantage of them. Let’s take a look at the best technologies being used in 2020.

White Box Testing (SAST)

One of the older technologies that has been around for over 10 years is white box testing. It is commonly referred to as Static Application Security Testing (SAST). This technology is useful for detecting software vulnerabilities early in the software lifecycle. These issues can be detected through their file name and line number. Additionally, it has in-built adherence to coding regulations. There is, however, a tendency for some false negatives and positives to be detected. The technology can also be somewhat complex, which can lead to issues in implementation. They are also not able to find defects outside the application code such as in third-party interfaces. Typically, SAST can find 14% of vulnerabilities within a code. This makes it useful, but it also means that other technologies should be used as a part of a comprehensive security structure.

Black Box Testing (DAST)

A supporting technology that is often used alongside the above testing method, is black-box testing. This is known as Dynamic Application Security Testing (DAST). Some organizations tend to wonder about sast vs dast. In truth, rather than selecting one over the other, it is far better to use them together. DAST can detect security vulnerabilities in running applications. Runtime problems can also be detected with ease. Unlike SAST, the exact line of code is not always able to be located. DAST requires a running application which means they can also be used later in the life cycle. Overall, the dynamic approach allows this technology to detect memory leaks, SQL injections, and many other real work vulnerabilities. It is helpful to use it before an application goes live.

Interactive Application Security Testing (IAST)

Both DAST and SAST have been around for a while. They are still reliable, but they shouldn’t be thought of as complete solutions for dealing with ever-evolving modern threats. IAST is a newer technology aimed to plug these gaps and to provide a more comprehensive security solution. This technology works through the placement of an agent directly within an application. It can scan the entirety of the code within an application which makes it very useful for catching all types of security flaws and vulnerabilities.

Runtime Application Security Protection (RASP)

Similar technology to IAST is RunTime Application Security Protection.  Instead of directly testing, it acts as a potent security technology that is effective at keeping threats out. It is placed within an application and allows consistent security checks to be conducted. Protection can be gained even when specific vulnerabilities are exposed. This makes it a fantastic technology to use in addition to other security solutions. It is even capable of responding to and neutralizing any live attacks. Security teams, however, should not solely rely on RASP. Instead, they should remember that even if attacks are prevented, the underlying flaws would still require a fix.

Reducing False Positives

No technology is completely infallible, and false positives are to be expected due to a variety of factors. Generally, there is a way to significantly reduce the number of false positives picked up by these technologies. This can be achieved through the use of abstract interpretation algorithms. For the best results, they should be specifically tailored to the application domain.

Challenges of Combining Tools

One type of tool isn’t enough to provide full security, and therefore a variety of solutions should be implemented. Know that combining tools isn’t always easy, and there are certain considerations to take into account. One specific challenge comes from the fact that each tool will have different naming conventions and severity ratings. This can cause issues when you look to rank vulnerabilities and decide on the best course of action. In this instance, it is worth using cross-referencing tools to determine the threats to your application. It is well worth the extra time and effort involved in utilizing these tools since a security breach can be incredibly costly. Organizations are becoming far more aware of these threats in 2020, and this has led to an increased usage of all of these various security technologies.

Summary

Overall, there is no technology better than the other. Rather, it depends on how they are used, and many are more effective when used together. Getting these combinations correct and utilizing the latest technologies should be a key security priority for all organizations. That’s all for today. Hope you find this article useful. If you have any questions, you can approach me in the section below, I’d love to help you the best way I can. Thank you for reading the article.

Taking Care of Your Machines

Hi Friends! Hope you’re well today. I welcome you on board. In this post today, I’ll walk you through how to take care of your machines. When you own a business, more likely than not, your business has machines or software that occasionally need maintenance. Sometimes these things can happen abruptly and bring a halt to the flow of your business. That is why it is important to know your machines or software well and know when a maintenance job on them is needed. The worst thing that can happen to you and your business is for a machine or software to stop working when you are at your busiest. That can hurt your business.

Knowing Your Equipment

Knowing your equipment inside and out is a huge asset to your company. This will save you both time and money in the long run because you will not have to keep bringing in a repair guy or IT guy to fix your problem. Fewer problems to fix means more time working and bringing in money. If you spend less money on repair people that means more money in profits, which means your wallet will feel a bit heavier. The first thing you can do is when you purchase your equipment, you can take time to learn about it inside and out. That way, if something does go astray, you will know what could be wrong and how to fix it. You may even be able to notice signs of your equipment starting to deteriorate so you can tackle the problem before it becomes a hindrance to you making money. As you know well, money is everything when it comes to business and you do not want to lose any of it.

How You Can Be Prepared For Anything

Being unprepared can be a death sentence for your business. If a machine or software you use daily goes and you are not ready, that is not good. The first thing you can do is make someone come in and do a monthly check-up. Now while this would keep you prepared, it would be very costly, and depending on your budget, it may not be worth it. Something you can take a look at is the fault protection machine learning solution. This will analyze your equipment’s working conditions and predict future failures or problems that may arrive. It is a much cheaper option than having a guy come out routinely and having to check on your equipment. In the end, knowing your business also means knowing the equipment and software you use every day to make your business run. It is not an exciting thing but it is an important one. Being unprepared for equipment or software to fail may not be a death sentence to a company, but it will be a thorn in your side for a long time. The best thing you can do is educate yourself on all your available options. In today’s world, it is becoming more and more likely that your work will be done on some sort of equipment or software. Do not be that business that loses customers because you were unprepared. That’s all for today. I hope you find this article useful. If you have any questions, you can approach me in the section below. I’d love to help you the best way I can. Thank you for reading the article.