The Engineering Projects

Introduction to BC327

Hi Friends! Glad to see you here. I welcome you on board. In this post today, I’ll be discussing the Introduction to BC327. BC327 is a bipolar junction transistor that falls under the family of PNP transistors. It is composed of silicone material and is used to drive load under 800mA. It’s a current-controlled device that carries three pins where small current generated at the one terminal is used to control large current at the other terminals. Read this post all the way through as you’ll get to know all nuts and bolts of BC327 covering pinout, working, power ratings, applications, and physical dimensions. Let’s get started.

Where To Buy?
No.	Components	Distributor	Link To Buy
1	BC327	Amazon	Buy Now

Introduction to BC327

• BC327 is a PNP bipolar junction transistor that comes in the TO-92 package and is used for switching and amplification purpose.
• It comes with three pins named emitter, base, and collector that are mainly used for external connection with the electronic circuit.
• BC327 is incorporated with three layers where one n-doped layer is sandwiched between two p-doped layers. The n-doped layer is negative while the p-doped layer is positively charged.

• This transistor incorporates 800mA collector current, hence it is easily employed to drive a variety of heavy loads.

• Collector dissipation is 625mW while the maximum current gain is 630 which makes it a suitable pick for audio amplification purposes.
• Transistors are mainly divided into two types named NPN and PNP transistors this BC327 transistor belongs to the PNP transistor family.
• Both transistors are different in terms of their charge carriers used for conductivity.
• Electrons are major carriers in NPN transistors while holes are major carriers in PNP transistors.
• When two diodes are combined from the cathode side, they constitute a PNP transistor where the N-doped layer represents the base side while the other two p-doped layers represent the emitter and collector respectively.

• You know it already, the movement of electrons is far better and faster than the movement of holes. The reason NPN transistors have a leg over PNP transistors for their quick response in conductivity.

BC327 Datasheet

• To understand the component thoroughly, it’s always wise to sift through the datasheet.
• Download BC327 Datasheet by clicking the button below:

BC327 Pinout

BC327 comes with three pins named 1: Emitter 2: Base 3: Collector The following figure shows the pinout of BC327.

• These pins are used for external connection with the electronic circuit. The small current change at the base terminal produces a large current change across other terminals.
• The base terminal plays a key role in differentiating both NPN and PNP transistors.
• In NPN transistor current flows through the base side when voltage is applied while in PNP transistor no current flows through the base terminal when the transistor is turned ON.

BC327 Working Principle

• When current flows through the base terminal in this PNP transistor, the transistor is turned OFF, and on the other hand, when there is no current at the base side, the transistor is turned ON.
• PNP works the same as NPN transistor but in the opposite fashion. The base still controls the large current across other terminal but here current flows in the opposite direction i.e. from emitter to collector.
• And instead of electrons emitted in the case of NPN transistor, holes are emitted by the emitter in PNP transistor that are then collected by the collector.

BC327 Power Ratings

The following table shows the absolute maximum ratings of BC327.

Absolute Maximum Ratings BC639
No.	Rating	Symbol	Value	Unit
1	Collector-Emitter Voltage	Vce	45	V
2	Collector-Base Voltage	Vcb	50	V
3	Emitter-Base Voltage	Veb	5	V
4	Collector Current	Ic	800	mA
5	Collector Power Dissipation	Pc	625	mW
6	Junction Temperature	Tj	150	ºC
7	Storage Temperature	Tstg	-55 to 150	ºC

• These are stress ratings that can make or break your entire project. Make sure ratings don’t exceed these absolute maximum ratings else you may compromise your component.
• Similarly, if these ratings are applied for more than the required time, they can affect the reliability of the device.

Difference between PNP and NPN Transistors

• The BC327 transistor carriers the same characteristics as NPN transistors with a few exceptions.
• In the case of PNP transistors, all current directions and voltage polarities will be reversed compared to NPN transistors.
• The NPN transistor sources current through the base terminal while PNP sinks current into the base terminal, the reason it’s also called a sinking device.
• In PNP transistor the base terminal is more negative than the emitter terminal. And all these terminals are different in terms of their doping concentration.
• The emitter terminal is highly doped and comes with 100% current of the transistor while the base terminal is lightly doped and is responsible for the transistor action and controls the number of holes emitter from the emitter which are then collected by the collector.

• The collector terminal is bigger compared to other terminal and is lightly doped.
• Both NPN and PNP also differ with respect to the applied source voltage i.e. in case of NPN transistor source voltage is applied at the collector side while in case of PNP transistor source voltage is applied at the emitter side.
• A load resistor is also used while working with this BC327 PNP transistor that controls the current in the collector terminal.
• Plus, biased voltage is applied at the base terminal that initiates the transistor action and it is coupled with the base resistor to resist and limit the current flowing through this terminal.

BC327 Alternatives

The following are alternatives to BC327.

• 2N4403
• BC488
• BC638
• 2N4402
• 2N3702
• 2N3703
• BC486
• BC490
• BC328

The pinout settings of the alternative may differ from the actual BC327. It’s wise to check the pinout of the transistor before employing it in your electronic circuit. NPN Complementary of BC327 is BC337. Since they both form a complementary pair, they can be employed together in many electronic projects.

BC327 Applications

BC327 comes with the following applications:

• Used for signal amplification and switching purposes.
• Finds application microcontrollers to drive heavy loads.
• Used in audio amplifiers and multiple preamplification stages.
• Employed to drive loads under 800mA.
• Used in push-pull configuration circuits.
• Used in medium-speed switching and high-frequency amplifiers.

BC327 Physical dimensions

The following figure shows the physical dimensions of the BC327. That’s all for today. I hope you find this read useful. If you have any questions, you can approach me in the section below. I’d love to help you the best way I can. Keep us updated with your valuable feedback and suggestions, they help us create quality content. Thank you for reading this post.

Introduction to BC550

Hi Guys! Happy to see you here. Thank you for viewing this read. In this post today, I’ll walk you through the complete Introduction to BC550. BC550 is a low-power low-frequency general-purpose bipolar transistor. It is mainly used to drive loads under 100mA. BC550 carries three terminals where a small current across one terminal is used to control the large current across the remaining terminals. It’s primarily used for amplification and switching purposes. Transistors are critical components and building blocks of modern electronic circuits. Bipolar junction transistors are divided into two main types named NPN transistors and PNP transistors. The BC550 falls under the category of NPN transistors and is available in a plastic TO-92 case. I suggest you read this entire post all the way through as you’ll get to know all nitty-gritty of BC550 i.e. datasheet, pinout, working principle, power ratings, applications, and physical dimensions.

Keep reading.

Where To Buy?
No.	Components	Distributor	Link To Buy
1	BC550	Amazon	Buy Now

Introduction to BC550

• BC550 is an NPN bipolar junction transistor mainly used for switching and amplification purpose.
• It incorporates three pins called the emitter, base, and collector. Where small current change at the base terminal is used to induce large current change across other terminals.
• BC550 carries three layers i.e. two N-doped layers and one P-doped layer. The P-doped layer indicates a positively charged layer that stands between the two N-doped layers that are negatively charged.
• When this transistor acts as a switch it is used to turn ON and OFF the input signal. When a powerful signal passes through the transistor, it turns ON the switch while lack of signal turns the switch OFF.
• When several thousands of millions of transistors are formed together, they can be incorporated into integrated circuits or in discrete components.
• BC550 is composed of semiconductor material. Silicon is mostly used to form these NPN transistors.
• In this NPN transistor, electrons are the majority carriers used for conductivity as opposed to PNP transistors where conductivity is carried out with holes as majority carriers.
• It is important to note that the movement of electrons is far better and faster than the movement of holes, the reason NPN transistors are better, thus preferred over PNP transistors.
• The main difference between NPN and PNP transistors is the behavior of the base terminal. In NPN transistors, current flows through the base terminal while in the case of PNP transistors no current flows through the base terminal when a transistor is ON.
• Also, the current flows from collector to emitter in NPN transistors, and in PNP transistors current flows from emitter to collector.
• Computer circuit boards are the common example of NPN transistors that carry millions of transistors used to store memory in the form of binary code.

BC550 Datasheet

• To understand the component thoroughly, it’s always wise to scan the datasheet.
• You can download BC550 Datasheet by clicking the button below:

BC550 Pinout

BC550 comes with three pins called

1. Emitter
2. Base
3. Collector

The following figure shows the pinout of the BC550:

• All these terminals are different in terms of their doping and functions.
• The emitter terminal is highly doped compared to the other two terminals.
• The emitter emits the electron into the base terminal which controls the number of electrons. The collector terminal is used to collect the number of electrons.

BC550 Pin Configuration

BC550 can be embedded in the following three configurations:

1. Common emitter configuration
2. Common collector configuration
3. Common base configuration

• Mostly amplification is carried out using a common emitter configuration as it comes with the exact voltage and current ratings required for amplification purposes.
• The amplification factor is an important factor used to define the nature of amplification. It’s a ratio between collector current and base current and is denoted by ß.
• The current gain is another factor which is a ratio between collector current and emitter current. It is denoted by a and is known as alpha. The alpha value ranges from 0.95 to 0.99 but mostly its value is taken as unity.

BC550 Working Principle

• In BC550, the base works as an electron valve that controls the number of electrons. When a voltage is applied across the base terminal, it triggers the electron reaction. Thus, the emitter starts emitting the electrons into the base terminal which are then collected by the collector.
• A small change in input voltage at the base terminal produces a large change in output voltage across other terminals. This phenomenon is used for amplification purposes.

• The collector voltage is always positive with respect to the emitter terminal while the base terminal is positive with respect to the emitter.
• And the collector terminal is combined with the load voltage using a resistor which is used to control the flow of current.

BC550 Power Ratings

The following table shows the absolute maximum ratings of BC550:

Absolute Maximum Ratings BC639
No.	Rating	Symbol	Value	Unit
1	Collector-Emitter Voltage	Vce	45	V
2	Collector-Base Voltage	Vcb	50	V
3	Emitter-Base Voltage	Veb	5	V
4	Collector Current	Ic	100	mA
5	Collector Power Dissipation	Pc	500	mW
6	Junction Temperature	Tj	150	ºC
7	Storage Temperature	Tstg	-55 to 150	ºC

• Emitter-Base voltage is 5V, which means the only 5V is required to trigger the base terminal, thus the entire transistor. While Collector-Base and Collector-Emitter voltages are 50V and 45V respectively.
• The collector current is 100mA i.e. it can drive loads with a value under 100mA.
• It’s wise to do your due diligence before incorporating this tiny device into your project as values exceeding absolute maximum ratings can severely damage the component.
• Plus, make sure you don’t apply these values for more than the required time, else they can affect the device's reliability.

BC550 Alternatives

BC550 equivalent are:

• BC546
• BC547
• BC548
• BC549

The complementary PNP transistor of the BC550 is BC560. BC550 Applications

• Used for amplification and switching purposes.
• Can be employed in the current mirror and H-bridge circuits.
• Used in linear amplifier and impedance buffering.
• Finds applications in oscillator and comparator circuits.
• Used in Astable and Bistable multivibrator circuits.
• Used for pre-amplification stages in electronic circuits.

BC550 Physical dimensions

The following figure shows the physical dimensions of the BC550: That’s all for today. Hope you’ve got a clear insight into the Introduction to BC550. You’re most welcome to ask your queries in the section below. I’d love to help you the best way I can. Feel free to keep us updated with your valuable suggestions and feedback. Thank you for reading this post.

Introduction to BC639

Hi Friends! Happy to see you here. I welcome you on board. In this post, I’ll walk you through the Introduction to BC639. BC639 is a high current gain bipolar junction transistor that falls under the NPN transistor family. It constitutes a high collector current and low collector-emitter saturation voltage and is widely used for amplification and switching purposes. It is used to drive load under 500mA. Collector Dissipation is 0.625W while DC Current Gain (hfe) ranges from - 40 to 160 with transition frequency 200MHz. In this post, I’m going to discuss all nitty-gritty of the BC639 transistor covering pinout, working, power ratings, alternatives, applications, and physical dimensions. Continue reading.

Introduction to BC639

• BC639 is an NPN bipolar junction transistor that carries high collector current and low collector-emitter saturation voltage.
• It is composed of silicon material and comes in a TO-92 package.
• BC639 carries three pins named emitter, base, and collector.

• It is mainly known as a current-controlled device where the base terminal is responsible for the entire transistor action.
• BC639 contains three layers where one p-doped layer sits between two n-doped layers.
• The small input current change at the base terminal is used to control large output current at the other two terminals.
• The base terminal controls the flow of electrons and acts as a control value. The emitter terminal emits the electron passing through the base terminal which are then collected by the collector terminal.
• Both electrons and holes play a critical role in conductivity carried out by these tiny components. In the case of NPN transistor electrons are the major charge carriers while in the case of PNP transistors holes are major carriers.
• The movement of electrons is faster and better than the movement of holes for conductivity. The reason these NPN transistors are preferred over PNP transistors for the making and execution of electronic projects.

Where To Buy?
No.	Components	Distributor	Link To Buy
1	BC639	Amazon	Buy Now

BC639 Datasheet

• It’s always wise to scan through the datasheet and get a hold of the main features of the component.
• Download BC639 datasheet by the link given below:

BC639 Pinout

BC639 comes with three pins called 1: Emitter 2: Base 3: Collector The following figure shows the pinout of BC639. Recall, BC639 is used to amplify the weak signal. As this is an NPN transistor, here current flows from collector to emitter as opposed to PNP transistor where current flows from emitter to collector. All these terminals are different in terms of their functions and doping concentrations. The emitter side is highly doped as opposed to the other two terminals. These pins are used for external connection with the electronic circuits.

BC639 Pin Configuration

BC639 transistor is employed in the following three main configurations:

• 1: Common emitter configuration
• 2: Common collector configuration
• 3: Common base configuration

• Common emitter configuration is used for the amplification purpose as it contains the suitable voltage and current ratings needed for amplification purposes.
• The nature of amplification is demonstrated by the amplification factor that is a ratio between collector current and base current. It is denoted by ß.
• The current gain is another important factor used to describe the nature transistor. It is a ratio between collector current and emitter current. It is called alpha and is denoted by a. The alpha value stands from 0.95 to 0.99 but frequently its value is taken as unity.

BC639 Working Principle

• It all starts from the base terminal. When the voltage is applied at the base pin, it ignites the electron reaction inside the transistor. This base pin controls the number of electrons emitted by the emitter terminal. The base pin acts as an electron valve and is responsible for conductivity inside the entire component.
• When BC639 acts as an amplifier, the small current at the base terminal (which acts as an input current) is used to control a much larger electric current at both emitter and collector terminals.
• And when it operates as a switch, it converts the small current at one part of the transistor into a much larger current across the remaining parts of the transistor.
• The base pin is positive with respect to the emitter terminal and collector voltage is always positive with respect to the emitter terminal.
• It’s important to note that the collector terminal is combined with the load voltage using resistor that limits and controls the flow of current.

BC639 Power Ratings

The following table shows the absolute maximum ratings of BC639.

Absolute Maximum Ratings BC639
No.	Rating	Symbol	Value	Unit
1	Collector-Emitter Voltage	Vce	60	V
2	Collector-Base Voltage	Vcb	60	V
3	Emitter-Base Voltage	Veb	5	V
4	Collector Current	Ic	500	mA
5	Current Gain	hfe	-40 to 160
6	Transition Frequency	ft	200	MHz
7	Storage Temperature	Tstg	-55 to 150	C

• Both collector-emitter and collector-base voltages are 60V while the emitter-base voltage is a mere 5V, which means the only 5V is required to trigger the electron reaction at the base terminal. And collector current is 500mA which projects that it can drive load under 500mA.
• The storage junction temperature range is -55 to 150C. While collector Dissipation is 0.625W and DC Current Gain (hfe) ranges from - 40 to 160 with transition frequency 200MHz.
• These are stress ratings that define the working of a component under certain values.
• If these values exceed the absolute maximum ratings, they can damage the component, thus the entire project.
• Do your due diligence before applying this component into your project and make sure you work under these mentioned ratings.
• Also, if these ratings are applied more than the required time, they can affect device reliability. Be careful.

BC639 Alternatives

KSC1009C transistor can be replaced by BC639. The complementary transistor of BC639 is BC640.

BC639 Applications

BC639 is used in the following applications:

• Used for amplification and switching purposes.
• Used in oscillator and comparator circuits.
• Employed in the current mirror and H-bridge circuits.
• Used for pre-amplification stages in electronic circuits.
• Finds applications in linear amplifier and impedance buffering.
• Incorporated in oscillator and comparator circuits.
• Used in Astable and Bistable multivibrator circuits.

BC639 Physical dimensions

The following figure shows the physical dimensions of the BC639. This is it. I hope you find this article helpful. I strive to share easy to read and easy to digest information. If you are unsure or have any question, you can pop a comment below, I’d love to help you the best way I can. Keep sharing your valuable feedback and suggestions, they help us create quality content. Thank you for your precious time.

Introduction to BC549

Hi Friends! I hope you’re well today. I welcome you on board. In this post, I’m going to discuss the Introduction to BC549. BC549 is a general purpose bipolar junction transistor that belongs to NPN transistor family. It contains three pins where small current change in one terminal produces a much large current change across other terminals. In other words, it is nothing but a current booster. It is known as a low power low voltage current controlled device and is used for switching and amplification purpose.  In this article I’ll be discussing complete details of BC549 transistor i.e. pinout, working principle, power ratings, physical dimensions and applications. Stay tuned.

Introduction to BC549

• BC549 is an NPN general-purpose bipolar junction transistor. It carries three pins named emitter, base, and collector and is available in TO-92 and SOT54 package.
• BC549 transistor contains three layers i.e. two N-doped layers and one P-doped layer. The P-doped layer stands between two N-doped layers. Plus, it contains two PN junctions where one is forward biased and the other is reverse biased.

• When no voltage is applied at the base terminal it is considered as grounded. In this case, the transistor acts like an open switch where both emitter and collector remain open.
• When voltage is applied at the base terminals it gets biased and draws current which is used to connect other terminals and current starts flowing from collector to emitter terminal.
• As this is an NPN transistor, here current flows from collector to emitter when voltage is applied, unlike PNP transistor where current flows from emitter to collector.
• Plus, both electrons and holes play a vital role in conductivity. In NPN transistor electrons are majority charge carriers and in PNP transistor holes are majority carriers.
• The movement of electrons, however, is faster than the movement of holes, the reason NPN transistors are better and faster than PNP transistors.

BC549 Pinout

BC549 comes with three pins named:

• 1: Emitter
• 2: Base
• 3: Collector

Following figure shows the pinout diagram of BC549.

• All three pins are used for external connections with other circuits. These pins are different in terms of operation and doping concentration.
• The collector voltage is larger than the base voltage and emitter terminal is highly doped compared to other terminals.

BC549 Pin Configuration

BC549 transistor can be employed in three main configurations as follows:

• Common emitter configuration
• Common base configuration
• Common collector configuration

Common emitter configuration is mostly used for amplification purposes as it contains the exact current and voltage ratings required for amplification.

• The amplification factor is called beta and is denoted by ß. It is mainly used to define the nature of amplification. It’s a ratio between collector current and base current. In BC549, the amplification factor ranges from 420 to 800.
• Another important factor is the current gain which is a ratio between collector current and emitter current. It is known as alpha and is denoted by a. The alpha value stands from 0.95 to 0.99 but more often than not its value is taken as unity.

BC549 Working Principle

• In BC549, emitter-base voltage is 5V which means when 5V is applied at the base terminal it gets biased and triggers the electron reaction.
• In the NPN transistor, the base terminal behaves like a control valve that controls the number of electrons.
• When voltage is applied at the base terminal, emitter starts emitting the electrons into the base terminal which controls the number of electrons. These emitted electrons passing through the base are collected by the collector terminal of the transistor.
• Moreover, the collector current is a mere 100mA i.e. you cannot drive heave loads using this transistor.
• As the only 5V is required to start the electron reaction at the base terminal, it can be easily employed across microcontrollers and microprocessors.
• When BC549 operates as an amplifier, small current as an input signal at the base terminal is used to induce a much bigger electric current at the other terminals.
• And when it works like a switch, it switches the small current at one part of the transistor into a much larger current across the other parts of the transistor.
• When transistor acts as a switch, it carriers two distinct states i.e. values are stored in the form of zero and one. Memory chip used in a computer is a common example of an electronic device that contains billions of transistors which can be turned on and off individually.

BC549 Power Ratings

Follow figure shows the absolute maximum rating of BC549:

• Emitter-Base voltage and Collector-Emitter voltages are 5V and 30V respectively.
• And Collector-Base voltage is 30V with collector current 100mA i.e. it cannot drive loads carrying ratings more than 100mA.
• The current gain ranges from 420 to 800 and transition frequency is 100MHz.
• These are stress ratings. Before you employ this transistor into your project and execute, make sure the ratings don’t exceed from absolute maximum ratings, else they will damage the product, and worse, your entire project, eventually.
• Also, if these ratings are applied for more than the required time, they can affect device reliability.

BC549 Alternatives

The following are the alternatives of a BC549 transistor.

• BC547
• BC548
• BC550

The PNP complementary of BC549 are:

• BC559
• BC560

BC549 Applications

BC549 can be used in the following applications:

• Used in liner audio amplifiers.
• Employed in Darlington pairs and sensor circuits.
• Used in oscillator and comparator circuits.
• Finds application in current mirror circuits.
• Used in Astable and Bistable multivibrators.
• Used for impedance buffering and switching applications.
• Finds application in low noise stages in audio frequency equipment.

BC549 Physical dimensions

Follow figure shows the physical dimensions of BC549: That’s all for today. Hope you find this article helpful. If you are unsure or have any question, you can approach me in the section below. I’d love to help you the best way I can. You’re most welcome to keep us updated with your valuable feedback and suggestions, they help us produce quality content. Thank you for reading this article.

Introduction to BC548

Hi Friends! Glad to see you here. I hope you’re well today. In this post, I’ll walk you through the Introduction to BC548.  BC548 is a general-purpose transistor that falls under the family of NPN transistors. It carries three pins that are mainly used for external connection with the circuit. The small current at one terminal is used to control the large current at other terminals. Moreover, it can drive loads under 500mA and is available in TO – 92 package. I suggest you read this post all the way through as you’ll get to know all nuts and bolts of BC548 transistor i.e. pinout, working principle, power ratings, applications, and physical dimensions. Let’s jump right in.

Introduction to BC548

• BC548 is an NPN general-purpose transistor, comes with three pins named emitter, base and collector.
• A small current at the base side is used to control large current at the collector and emitter terminals. The reason, it’s normally called a current controlled device.

• Decent current gain and power dissipation make it a suitable pick for amplification circuits and pre-amplification stages in other electronic applications. Moreover, it is also used as a switch to carry the load below 500mA.
• This BC548 transistor belongs to the NPN family where it contains three layers i.e. two N-doped layers and one P-doped layer. The P-doped layer is sandwiched between two N-doped layers.
• Also, it contains two PN junctions where one is reverse biased and the other is forward biased.
• The NPN transistor is like an electron valve where the base terminal controls the movement of electrons. It is widely used for amplification purposes in many electrical and electronics projects.
• Plus, electrons behave like majority carriers in NPN transistors whereas in PNP transistor holes behave like majority carriers. In conclusion, the mobility of electrons is better than the mobility of holes, thus NPN transistors are better and faster than PNP transistors.

1. BC548 Pinout

BC548 contains three pins named:

• 1: Emitter
• 2: Base
• 3: Collector

Following figure shows the BC548 pinout:

• All these terminals are different in terms of operation and doping concentration.
• The base terminal controls the current, emitter is used to emit the number of electrons when voltage is applied at the base terminal which is then collected by the collector.
• The small increase in input voltage applied at the base terminal produces a large change in output voltage across both collector and emitter terminals. This practice is used for amplification purposes.
• The emitter terminal is highly doped as compared to collector and base terminals. Plus, the collector voltage is larger than the base voltage.

2. BC548 Pin Configuration

BC548 transistor is used in three main configurations as follows:

• Common base configuration.
• Common emitter configuration.
• Common collector configuration.

Common emitter configuration carries exact voltage and current ratings mainly used for amplification.

• The amplification factor is used to define the nature of amplification. It is called beta and is denoted by ß. It is a ratio between collector current and base current. As it’s a ratio between the same factor i.e. current, it contains no unit. In this NPN transistor, the amplification factor ranges from 110 to 800.
• Similarly, the ratio between collector current and emitter current is called current gain and is mainly known as alpha, denoted by a. The alpha value lies between 0.95 to 0.99 but most of the time its value is taken as unity.

3. BC548 Working Principle

• When the base terminal is grounded, both emitter and collector terminals remain disconnected.
• When the voltage is applied at the base terminal, it gets biased, forming a bridge between collector and emitter.
• As this is an NPN transistor, the current will flow from collector to emitter, unlike PNP transistors where current flows from emitter to collector.
• Though both electrons and holes play a key role in conductivity, in the case of NPN transistors, electrons are major charge carriers.
• The base terminal controls the number of electrons passing from collector to emitter and appears positive with respect to the emitter terminal.
• The applied voltage at the base terminals draws a small current which is then used to police the large current at the collector and emitter terminals.

4. BC548 Power Ratings

The following figure shows the absolute maximum ratings of BC548:

• Collector-Base voltage is 30V. While Emitter-Base voltage and Collector-Emitter voltages are 5V and 30V respectively.
• The Collector current is 500mA with maximum power dissipation 625mW at temperature 25C.
• And the current gain ranges from 110 to 800.
• It’s important to note that these values are called stress ratings. Before you employ this transistor into the required circuit, make sure these ratings don’t cross the absolute maximum ratings, else you can risk your transistor and thus the entire project.
• Plus, if these ratings are applied for an extended period, they can influence the device reliability.
• Note: these values are measured at T = 25 C

5. BC548 Alternatives

The following are equivalent transistors of BC548:

• 2N2222
• 2N3904
• BC547
• BC549
• BC550

They all belong to the NPN family. The PNP complementary of BC548 is BC558. The type of transistor you use depends on the ratings of load you intend to drive i.e. in case of BC548 you can drive loads under 500mA.

6. BC548 Applications

NPN type transistors are used in circuits when you intend to sink the current. BC548 is used in the following applications:

• Used in Darlington pairs to amplify weak signals.
• It can be employed in sensor circuits.
• Driving loads under 500mA.
• Used in audio amplification.
• Used in audio Amplifier Stages.

7. BC548 Physical dimensions

The following diagram shows the physical dimension of the BC548: Recall, BC548 is a bipolar NPN junction transistor and is considered as a current-controlled device where small current at the base is used to control large current at the collector and emitter terminals. Plus, it can drive loads under 500mA and is available in TO – 92 package. That's all for today. I hope you find this read helpful. If you have any question, you can approach me in the section below, I'd love to help you the best way I can. Feel free to keep us updated with your valuable feedback and suggestions. They help us create quality content. Thank you for reading this article.

Introduction to BC546

Hi everyone! Thank you for viewing this article, I welcome you on board. In this post I’ll walk you through the detailed Introduction to BC546. BC546 is a low power NPN transistor mainly used for general purpose amplification and switching applications. In this read you’ll study all nitty-gritty of BC546 transistor i.e. from pinout, pin configuration, and working principle to power ratings, key parameters, physical dimensions and applications. Keep reading.

Introduction to BC546

• BC546 is a bipolar junction NPN transistor that finds applications in switching, amplification, impedance, H-bridge and current mirror circuits.
• This transistor falls in silicon epitaxial planar transistor category which is generally divided into three groups A, B & C. This BC546 is available in group A & B.
• BC546 low power transistor mainly contains three terminals named emitter, base and collector. And all these terminals are different in terms of their doping concentration and are used for external connection with electronic circuits.
• BC546 transistor contains three layers i.e. two N-doped layers and one P-doped layer. The P-doped layer resides between two N-doped layers. Plus, it carries two PN junctions where one is forward biased and other is reverse biased.
• Unlike FET (Field-Effect Transistor) that is voltage controlled device, BC546 is a current controlled device where small current at the base terminal is primarily used for controlling the large current at both emitter and collector terminals.

1. BC546 Datasheet

• Although, we are going to discuss everything related to BC546, in this tutorial but still its always wise to have a look at the datasheet.
• You can download BC546 Datasheet by clicking the below button:

Download BC546 Datasheet

2. BC546 Pinout

BC546 carries three pins named

• Emitter.
• Base.
• Collector.

The collector voltage is much larger than the base voltage and emitter terminal is highly doped compared to base and collector terminals. When voltage is applied at the base terminals, it ignites the electron reaction between emitter and collector terminals.

3. BC546 Pin Configuration

• Emitter current is a sum of both collector current & base current.
• The small current at the base terminal is used to control large current at the emitter and collector terminals.
• This transistor can be employed in three main configurations named:
  • Common base configuration.
  • Common emitter configuration.
  • Common collector configuration.
• Common emitter configuration comes with exact voltage and current ratings required for amplification.
• Forward current defines the nature of amplification. It is called amplification factor, or beta and denoted by ß. Which is a ratio between collector current and base current and it carries no unit. The amplification factor ranges from -110 to 800.
• Similarly, current gain is a ratio between collector current and emitter current. It is known as alpha, denoted by a. The alpha value ranges from 0.95 to 0.99 but more often than not its value is taken as unity.

4. BC546 Working Principle

• BC546 is a junction transistor where both electrons and holes are responsible for conductivity, electrons are majority charge carriers, however.
• In NPN transistor base terminal is positive with respect to emitter and is usually used to control the number of electrons.
• It gets biased and draws current when voltage is applied at the base terminal, thus controlling the large current at emitter and collector side.
• Free movements of electrons plays a key role for conductivity and is mainly used to bridge the gap between emitter and collector where electrons are emitted by the emitter which are then collected by the collector.
• In this NPN transistor current flows from collector to emitter unlike PNP transistor where current flows from emitter to collector.

5. BC546 Power Ratings

Absolute maximum power ratings of this NPN transistor are shown in the figure below:

• Collector-Base voltage is 80V. And Emitter-Base voltage is 6V.
• High Collector-Emitter voltage of 65V makes it the best pick for high voltage audio amplifier applications.
• Collector current is 100mA with maximum power dissipation 500mW at temperature 25C.
• These are stress ratings that, if increased from absolute maximum ratings, can severely affect the quality of the product, thus damaging the device.
• Similarly, if these ratings are applied for the extended period of time, they can affect the device reliability.
• The absolute maximum ratings are stress ratings with values measured at T = 25C

6. BC546 Modes & Key Parameters

The current directions and voltage polarities are opposite in both NPN and PNP transistors. If current flows in a clockwise direction in NPN transistor and carries positive polarity at the base terminal, it will flow in an anticlockwise direction in PNP transistor negative voltage polarity. Flow of electrons from collector to emitter in this NPN transistor depends on the biased voltage applied at the base terminal. Following are four modes of BC546 transistor:

• Active mode.
• Cut-off mode.
• Saturation mode.
• Reverse-active mode.

Base terminal is also called the active mode, and is mainly responsible for transistor action, where voltage is applied that draws small current which is then used to control large current at the emitter and collector terminals. In cut-off mode transistor acts like an open switch and no current flows between the terminals. Saturation mode acts like an ON switch where current flows from collector to emitter. In this condition the voltage difference between collector and emitter is zero. In reverse active mode transistor acts like an active mode but here current direction is reversed, now it flows from emitter to collector.

7. BC546 Alternatives

BC546 contains following alternatives:

• 2SC4145
• 2SD1698
• 2SD1701
• 2SD1978
• 2SD1981
• 2SD2296A
• 2SD2213
• HIT667
• KTC1026
• KTC3200

All transistors mentioned above are NPN transistors and are composed of silicon material. While its complementary types PNP transistors are BC556 & BC559.

8. BC546 Applications

BC546 is mainly used in the following applications:

• It is used in linear amplifiers.
• BC546 finds applications in H-Bridge circuits
• Used for impedance circuits and current mirrors circuits
• Also employed in oscillator circuits and Astable vibrators
• Used in bistable multivibrators and comparator circuits

9. BC546 Physical dimensions

Following diagram shows the physical dimension of BC546: All three terminals are 0.492in in length and 0.181in in width with distance between two terminals 0.142in. This transistor carries weight approx. 0.18g. That's all for today. I hope you’ve got clear idea about BC546 transistor. If you are unsure or have any question, you can ask me in the section below, I'd love to help you the best way I can. You’re most welcome to keep us updated with your valuable feedback and suggestions. Thank you for your precious time.

Introduction to ADC0804

Hello friends, I hope you all are doing great. In today’s tutorial, we will have a look at Introduction to ADC0804. In electronic engineering different modules used to conversion of analog signal into a digital signal. These tools are recognised as analog to digital converter or ADC. Thes signal converter also used to find the value of input current and voltage. Normally the output of these converters are 2 binary numbers but other values are also possible. These analog to digital converter are available in different structure scheme but mostly they are available in integrated circuits packaging. The working ability of these signal converter depends on their bandwidth and signal to noise ration (SNR). Their bandwidth can be fined by their sample rate (sample rat is the elimination of a continuous-time signal to a discrete-time signal). The signal to noise ratio can be measured by the resolution (resolution of the converter designates the number of discrete values it can create over the series of analog values), accuracy of signal, aliasing (It is an effect that makes different signals to become indistinguishable). In today's post, we will have a look ADC0804 analogue to digital converter, its pinout working, applications, advantage and some other related parameters. So let's get started with Introduction to ADC0804.

Introduction to ADC0804

• The ADC0804 is integrated circuitry that used to transform anlog input into the digital output. This eight-bit analog to digital converter has twenty pinouts.
• This integrated circuit is mostly used in different microcontrollers such as Raspberry Pi etc. To triggering this ADC module there is no need of external clock this module has its own clock.

• This component is the best choice if you are looking such analog to digital converter having the finest resolution and eight bits.
• Earlier microcontrollers do not consist of analoge digital converter that used separate hardware for this purpose but currently, microcontrollers comprise of the ADC converter.
• These signal converter mostly used for temperature measurements like in homes or industries to measure the temperature of heating elements used in different machines. In automobiles like a car, it also used for measurement of temperature.
• This module is not used only for the temperature calculation but used in such applications where analog signal is used.

Pinout of ADC0804

• These are the main pinouts of this module that are described here with the detailed.

Pin No:	Pin Name:	Parameters
Pin#1	Chip Select  Pinout	If more than one analog to digital converter is working with this module.
Pin#2	Read command pinout	This pinout should be grounded to read the analog signal.
Pin#3	Write command	For data, conversion this pinout has a large pulse.
Pin#4	Clock in command	The exterior clock signal can be linked at this pinout.
Pin#5	Interrupt	Interrupt command is provided at this pinout.
Pin#6	Vin positive	For differential analog input attach analog to digital converter here.
Pin#7	Vin negative	For differential analog input, link to ground terminals.
Pin#8	Gnd	At his pinout analog ground terminal is connected.
Pin#9	reference voltage	This pinout is used to provide reference voltage during analog to digital conversion.
Pin#10	Gnd	At this ground pinout, the digital ground is connected.
Pin#11 to 18	Data bit 0 to bit 7	Seven output Data bit pins from which output is obtained
Pin#19	Clock R	This is RC timing resistor input pinout for interior clock generator.
Pin#20	Data Pin 6	This pinout is used to connect input plus five volts for analogue to a digital module.

Features of ADC0804

• These are some features of ADC0804 that describe with detail.
• This module can easily connect with other microcontroller and can also work alone in any circuitry.
• This is eight-bit analog to digital converter module.
• At this module, interior clock exists there is no need of special clock oscillator.

• Its digital output values change from zero to two fifty-five volts.
• This module is available in twenty pinouts PDIP (dual inline packaging) and SOIC (small outline integrated circuits) packaging.
• It takes one hundred ten microseconds for the conversion of analoge to digital values.
• Its interior clock frequency is six fort kilo-hertz.
• It can measure the voltages from zero to five volts by operating on the five volts input supply.

Working of ADC0804

• Now we discuss the working of ADC0804 with the detailed.
• As we discussed above that this module consists of the interior clock and there is no need of any separate clock.
• But if for use of this interior clock we have to connect RC circuitry with this module. This module must be linked with the plus five volts power supply and both ground pinouts linked with the ground terminal of circuitry.
• For the construction of resistance-capacitor (RC) circuitry use ten-kilo resistance and capacitor of hundred pico-farads after that attached the pinouts CLK R and CLK in as shown in a given figure.
• The pinouts CS and R should be linked with the ground. The reference pinout is not connected with any point since it will be linked with the plus five volts.
• In given circuitry you can observe that the input analog voltage is provided at the IN (+) pinout and digital output will be obtained at the DB0 and DB7 pinouts.
• You can also see that the second terminal of a source is connected with the ground for analog to digital conversion.
• Before starting of analog to digital transformation the WR pinout should be high this condition can be obtained by linking this pinout with the input or output pinout of Microprocessing Unit and it set to high value.

• In the circuit you can also see that potentiometer is linked to varying the voltage from zero to five volts at the input pinout.
• In the given figure, you can also see that voltage value is 1.55 volts and its corresponding binary value is (01001111) .
• Now we discuss how we can  convert this binary value into the analog,
• As our binary value is (01001111)
• First of all, we convert it into decimal.

Binary  to Deci = (0 x128)+(1 x 64)+(0 x 32)+(0 x16)+(1 x 8)+(1 x 4)+(1 x 2)+(1 x1)

                                       =   79 Analoge value will be= Deci x step size

                             = (79) x (19.53)mV = (1.54)V

• As you can observe that obtained value is (1.54 volts) and 1,55 volts is measured value both of these are approximately close to each other.

Applications of ADC0804

• These are some applications of ADC0804, let's discuss with the detailed.
• It can function with an eight-bit processor.
•  Normally it used with the different microprocessors like Raspberry PI, Beagle Bone, etc.
• It can easily be linked with the sensing devices, voltage sources and transducers.

So, friends, it is the detailed tutorial on the ADC0804 if you have any question about ask in comments. Thanks for reading.

Introduction to PT2272

Hello friends, I hope you all are doing great. In today’s tutorial, we will have a look at Introduction to PT2272. It is a CMOS (complementary metal-oxide-semiconductor) that use to design simple wireless controlling of instruments installed at some distance. This module is normally used for controlling the circuits of garage door, speed control of the fan, robots and for monitoring the alarm connected at different places for security purposes. This integrated circuitry uses non-variable code address and no built-in encryption due to these parameters it not used for such circuits where high security is need but uses only for small or less cost security circuits such as used in home security alarms etc. In today's post, we will have a look at its working, pinout,  applications and some other related parameters. So let's get started with the Introduction to PT2272.

Introduction to PT2272

• The PT2272 is a decoder coupled with the PT2262 use the complementary metal-oxide-semiconductor technique.
• The use of PT2262 with this module to work as a transmitter for the PT2272 that work as a receiver and decodes the data sent by the transmitter.
• The output pinouts of this module are transistor-transistor logic that can be connected with the other circuitry and microcontroller.

• The operating voltage of the transmitter (PT2262) is five volts to twelve volts dc and the operation voltage of PT2272 are also five volts dc.
• This module consists of twelve bits of tri-state address pinout that offers three hundred twelve address codes.
• This module has features like large no of output data pinouts, latching and temporary output.
• The complementary metal-oxide-semiconductor technique (CMOS) technique used in this module offered the use of less power, less sound to noise ratio, twelve tri-state address pinouts, six data pinouts many ranges of voltages operation.
• This integrated circuitry is the finest option for security circuits used in different vehicles like cars, door alarm, robotic controls and some other home automation circuits.

Pinouts of PT2272

• Now we discuss the pinouts of PT2272 with the detailed, that is described here with the detail.

Pin No:	Pin Name:	Parameters
A0 to A5	Input pinout	These pinouts are address pinouts. All these six pinouts are used to get input coming from the transmitter and then encode the data.
A6/D5 ~ A11/D0	Input and output pinouts	These 6 pinouts are used for such data that has a large number of bits and also on the type of PT2272 module used.
DIN	Input pinout	When these pinouts are operating as inputs, these pins behave as tri-state input pinouts and every pin can set at the three different levels one, zero and floating. If we use these six pinouts as When used as output pins, these pins are driven to VCC if (1) the address decoded from the waveform that was received matches the address setting at the address input pins, and (2) the corresponding data bits received is a “1” bit. Otherwise, they are driven to VSS.
OSC 1	input pinout	It is oscillator pinout no one.
OSC 2	Output pinout	It is oscillator pinout number two. A specific value of resistance connected among them finds the value of the fundamental frequency of PT2272.
VT	Output	This pinout is used for the output gain
VCC	-	At this terminal positive input is provided.
VSS	-	This terminal is used to provide a negative supply.
NC	-	This is open pinout.

Features of PT2272

• These are some features of PT2272 that are described here with the detailed.
• This module used complementary metal-oxide-semiconductor (CMOS) technique.
• This module used a small amount of energy for its operation.
• Its provides larger immunisation from the noise.

• This module has twelve tri-state code address pinouts.
• This module has six data pinouts.
• Its operating volt re from four to fifteen volts.
• This module also consists of a single resistance oscillator.
• It is also available in dual in-line package and in small outline package.
• Its operating span is from five volts to twelve volts.
• Its input voltage is five volts dc.
• This module has already assembled light-emitting diode on its assembly.
• This module also has four outputs of transistor-transistor logic.
• Its transmitter is dimensions are thirty-six milli-meter by twenty-six milli-meters.
• Its receiver dimensions are forty-five to twenty-six millimetres.

Absolute Maximum Ratings of PT2272

• Now we discuss the ratings of PT2272 with the detailed.

Parameter	Symbol	Rating
Input Voltage	Input voltage denoted as VI.	The value of these voltages is -0.3 VCC+0.3 volts.
Supply Voltage	Denoted as VCC	The value of voltage is -0.3 to 16 volts.
Storage Temperature	This temperature denoted as Tstg.	The temperature value is -65 to 150 Celsius.
Operating Temperature	It denoted as Topr.	Temperature value from -40  to +85 celsius.
Output Voltage	This voltage denoted as VO.	This temperature is from -0.3 VCC+0.3 volts.

DC Electrical Features of PT2272

• Now we discuss the pinouts of PT2272 with the detailed, that is described here with the detail.

Parameter	Symbol	Conditions
Supply Voltage	This voltage denoted as VCC.	-
Stand-by Current	This current is denoted as ISB.	The conditions for this voltage is VCC is twelve volts. DIN is zero volts. OSC1 is zero volts.
DOUT Output Driving Current	It denoted as IOH.	The voltage VCC is eight volts. The voltage VOH is four volts.
DOUT Output Sinking Current	It is denoted as IOL.	The value of VCC is five volts. The value of VOH three volts.
“H” Input Voltage	This input voltage is denoted as VIH.	VCC
“L” Input Voltage	VIL	VCC

Applications of PT2272

• These are some applications of PT2272 described with the detailed.
• It uses in circuits of a different security system.
• It is used in circuits of automatic on and off of garage door circuits.
• It used for the automatic control fan speed circuits.
• Security circuits of home.
• It used in different robotics circuits.
• It used in industries for the control of different machines.

It is the detailed tutorial on the PT2272 if you have any question about it ask in comments thanks for reading.

Introduction to TIP35

Hello friends, I hope you all are doing great. In today's tutorial, we are gonna have a look at detailed Introduction to TIP35. It is a reliable silicon NPN transistor that is projected to use in common persistence amplification and swapping capitulations. It is existing in TO-247 that is no more used by most fabricators. It's corresponding transistor TIP36 which is PNP transistor. It is a communal transistor which is used in several industrial projects where audile magnification is required. Its structures are good-observing much the similar refusing for the exciting power acceptance that is rather lesser. In today’s post, we will have a look at its fortification, wreckage, eminence, claims, etc. I will also share some links where I have connected it with other microcontrollers. You can also get more material about it in comments, I will guide you more about it. So, let’s get started with a basic Introduction to TIP35. 

Introduction to TIP35

• It is a reliable silicon NPN transistor that is projected to use in common persistence amplification and swapping capitulations. It is existing in TO-247 that is no more used by most fabricators.

• This amplifier does not privilege to be 'state of the art' and in statistic the base enterprise times back to the initial 1970s.  It is a modest amplifier to construct, usages normally accessible fragments and is constant and consistent. 
• The scheme contained is a small adjustment of an amplifier which intended numerous ages back, of which hundreds were constructed. 
• This transistor catches wide use in Power Swap structures like inverters, and output stages of audile amplifiers where they are associated in push-pull with a matching power transistor type.
• Whenever it is used in an audio amplifier arrangement, it is practical to initiative the power transistor from a pre-amplifier stage as maximum power transistors have a slight gain of current.

Pinout of TIP35

• These are the pinout of TIP35 which is well-defined underneath.

• Pin#	Type	Parameters
  Pin#1	Emitter	The emitter is for an outdoor motion of current.
  Pin#2	Base	The base achieves the biasing of the transistor. It impulses the state of the transistor.
  Pin#3	Collector	The collector is for the current inner drive. It is linked to the load.

  Lest see a diagram of the pinout.

Features of TIP35

• These are the main features of TIP35.
  • It is offered in covering the type of TO-247.
  • This fits in NPN transistors.
  • The voltage put on at collector and emitter is 40 volts.
  • The voltage at collector and base points is 40 volts.
  • The voltage at emitter and base is five volts.
  • This transistor devours 25-ampere current at the collector.
  • The power forbearance at the collector point is 125 watts.
  • Its gain is about 15 to 75.
  • Its switching frequency is 3 Mhz.
  • Its functioning and stowage joining temperature range are -65 to +150°C.
  • This transistor is free from Lead (Pb).

Maximum Ratings of TIP35

Symbols	Ratings	Parameters
VCEO	60V	It is the voltage crosswise collector and emitter.
VCB	60 V	It is the voltage crosswise collector and emitter.
VEB	5.0 V	It is the voltage across emitter and base.
IC	25 V	It is the current at the collector.
IB	5.0 A	It is the value of current at the base point.
PD	125 A	It is the entire Power Indulgence at T = 25 C  overhead 25 C.
TJ, Tstg	-65 to +150	Working and Storing Connection Temperature Choice
ESB	90	It is the unclamped Inductive Load.

Electrical Characteristics

Symbols	Ratings	Parameters
VCEO	60V	These are C-E Supportive Voltage (IC = 30 mA, IB = 0)
ICEO	1mA	It is the collector and emitter Cut-off Current. (VCE = 30 V).
ICES	0.7mA	It is the collector and emitter Cut-off Current.
IEBO	1 mA	It is the emitter and base Cut off Current.
hFE	25 15	It is the DC current gain. (IC = 1.5 A, VCE = 15 V) (IC = 4 A, VCE = 4 V)
VCE	1.8 4.0	These are emitter and collector saturation voltage. (IC = 15 A, VCE = 1.5 V) (IC = 25 A, VCE = 5 V)
VBE	2V 4V	These are the Collector-Emitter Saturation Voltage. (IC = 15 A, IB = 4 A) (IC = 25 A, IB = 4 A)
ft	3V	It is the current gain-bandwidth product.

Working of TIP35

• Now we read about its working with a circuit diagram.
• In this circuit, I am going to show you 500W power inverter circuitry which using TIP35.
• In this circuit diagram, there is merely one adjustable resistance which is for changing the frequency of 240 AC output current.It is finest to use a frequency meter to regulate this frequency of 50HZ to 60HZ according to your requisite.Please avoid giving power any instrument by an inverter before changing the frequency according to your instrument.  Otherwise, it will damage your device.
• For further understanding, let's see the circuit diagram.

Applications of TIP35

• These are specific applications of TIP35.
  • It is cooperative obstinacy transistor it can be used in different industrial schemes.
  •  It is used as an audio Amplifier.

So it was all about TIP35 if you have any question please ask in comments. Take care until the next tutorial.

Introduction to TIP127

Hello friends, I hope you all are doing great. In today's tutorial, we are gonna have a look at detailed Introduction to TIP127. The TIP127 is a PNP type Darlington pair transistor. It is manufactured for universal drive amplifications and less velocity swapping submissions. It is existing in TO-220 kind of cascading. Its corresponding NPN transistor is the TIP122. This is a common transistor it used in varied engineering schemes. It formed for least time taking swap proposals. In today’s post, we will have a look at its protection, wreck, difference, entitlements, etc. I will also share some links where I have connected it with other microcontrollers. You can also get more material about it in comments, I will guide you more about it. So, let’s get started with a basic Introduction to TIP127.

Introduction to TIP127

• The TIP127 is a PNP type Darlington pair transistor. It is manufactured for universal drive amplifications and less velocity swapping submissions.
• It works similar to standard PNP transistor, then as it consists of a Darlington pair it takes collector current of around five amperes and a gain of near 1000.

• It has ability to endure around 100 volts at its collector Emitter terminals henceforth it used to run high current consuming loads.
• It has two limits on the power management aptitude of a transistor first one is normal intersection temperature and second one failure.
• If you are noticing for a PNP transistor for your amplifier electric circuit then TIP127 could be your brilliant choice or to alteration stylish current loads larger than 2A.

Pinout of TIP127

• These are the main pinout of  TIP127.

  Pin#	Type	Parameters
  Pin#1	Emitter	Current creates out by the emitter, it is characteristically linked to ground.
  Pin#2	Base	It accomplishes the biasing of the transistor and works to turn ON or OFF the transistor.
  Pin#3	Collector	Current movements in over collector, classically linked to load

  Let's see a diagram of the pinout.

Features of TIP127

• These are some important of TIP127. It is a PNP transistor.
  • The voltage at (C-E) terminals is a minus hundred (-100) volts.
  • The voltage it uses at (C-E) is minus (100) volts.
  • The voltage at emitter and base is minus five (-5) volts Emitter-Base Voltage:
  •  It uses current at collector is minus five (-5) amperes.
  • The power dissipation at the collector terminal is sixty-five (65) watts.
  • Its is Gain thousand (1000).
  •  Its Working and Storing Intersection Temperature Range is from minus sixty-five to plus one fifty Celsius(-65 to +150 °C).
  • It offered in TO-220 casing.

Ratings of TIP127

Symbols	Ratings	Parameters
VCBO	-60 Volts	These are the voltage across collector and base.
VCEO	-60 Volts	These are the voltage around collector and emitter.
VEBO	-5 Volts	These are the voltage around emitter and base.
IC	-5 amper	It is the current at collector which is dc.
ICP	-8 Amper	It is the pulse of collector current.
IB	-120 milliampere	It is the current at the base.
Pc	65 Watts	It is the power dissipation at  Collector (TC=25°C).
TJ	150 C	It is the Junction Temperature.

Electrical Characteristic of TIP127

Symbols	Ratings	Parameters
VCEO	-60 Volts	It is the Collector and Emitter Supporting Voltage
ICEO	-2 milliampere	It is the Collector Cut off Current.
VCBO	-1 milliampere	It is the value of Collector Cut off Current.
IEBO	-2 milliampere	It is the value of Emitter Cut off Current.
hFE	1000	It is the value of  Current Gain.
VCE	-2 volts	These are the Collector and Emitter Saturation Voltage.
VBE	-2.5 volts	It is the value of  Base and Emitter On Voltage
Cob	300 pF	This is the output capacitance.

 

Applications of TIP127

These are some important applications of TIP127 which are described below with detail description.

• It is used to run higher current devices such as loads which work on up to the five amperes.
• It works as the switch which consumes intermediate power during its working.
• It used in such circuits where higher amplification is required.
• It also used to in motors circuits to control their speeds.
• It also used in Inverter circuits and other rectifier circuits.

So, friends, I tried a lot to share my best knowledge about TIP127, if you have any question about it please ask in comments. I will resolve your problems in a comprehensive way. Thanks for reading. Take care until the next tutorial.